3924 - 3A St NE, Calgary, AB, T2E 6R4   Call us: 403-277-0152   general@universalcycle.ca / drayko@universalcycle.ca

• Flat rate shipping of $10 on orders over $150* • FREE SHIPPING on orders over $299*

*This offer applies to items under 10lbs / cubed weight. No PO BOX or RR Addresses.

• 10% OFF In Store Pick Up - Use coupon code: THANKYOUCALGARY

Service Dept.

On This Page:

Winter Service sale

Service Packages

Tire Service & Repair

General Maintenance

DynoJet Dyno

Boring Bar

Cylinder Heads

Mill & Lathe

We Also....

Tech Tip

Storage Tips

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

State of the Art Service Center

 

 

Seperator

Service Packages

custom image

 

custom image

 

 
Seperator
 
 
  
custom image
   
 
  
 Seperator
 
    
   
 custom image
 
 
 
Seperator
 
 
  
 
custom image
 
 

Seperator

General Maintenance

  • Shop Labour - $150.00 Per Hour
  • Tires
  • Oil Changes
  • Tune-Up's
  • Carb. Overhauls - Ultrasonic Carb. Cleaning
  • Heads, Barrels and Cases - NEW Ultrasonic Pro Cleaning
  • Vapor Blasting
  • TEXA - ECU / ECM Systems Control Management Analysis
  • Pre-Purchase Inspections - $190.00
  • Government / Out Of Province Inspections - $190.00 - We do not charge for a re-inspection if we performed the original inspection. If the motorcycle was inspected elsewhere and failed, we can complete the re-inspection but the full fee will be applied.
  • Salvage Recertification - $260.00 - The same re-inspection rules apply as stated above.
  • etc., etc....

 

Seperator

DynoJet Dyno

  • Dyno Tuning
  • Horsepower Readings
  • Torque Readings
  • Air / Fuel Ratio Monitor
  • Fully Computerized
  • For Bikes, Quads, Karts, Legends
  • Fuel Injection Programming
custom image
 

Seperator

Boring Bar

  • Precision Boring & Honing - $140.00 Per Hole 
  • Using a Cyclecyl Bore Master & Sunnen Hone Precision Honing macine Model - L88
  • Includes, on 2-Stroke - Chamfer Ports, 4-Stroke - Check ring end gaps 
  • Sleeving
  • O-Ring Blocks

 

Seperator

Cylinder Heads

  • Cut Seats
  • Install Guides
  • Face Valves
  • Porting
  • Using a Neway Valve Facer

 

Seperator

Mill & Lathe

  • Undercut Gears
  • Deck Blocks & Heads
  • Fabricate Parts

 

Seperator

We Also....

  • Press & True Cranks (Rod Kits)
  • Weld Cranks
  • Install Race Tech Suspensions
  • Rebuild and Sync Carbs., Exhaust Gas Analysis
  • Do Any Mechanical Work
  • No Job Too Big Or Small

 

Seperator

Tech Tip

Winter Storage Tips for YOUR Bike!

  • Drain dirty oil, change oil and filter. A hot oil change is best.
  • Drain the Carburetor fuel bowls.
  • Disconnect and remove the battery. Store inside and charge monthly.
  • Gas tank either full or empty. If full, add gas stabilizer. If empty, spray inside with WD-40.
  • Wash, dry and wax (polish) before storage to inhibit corrosion.
  • Cover bike with bike cover or soft blanket.
  • Store inside if possible, otherwise protect from the elements.
  • If stored outside, remove spark plugs and pour a small amount (1 teaspoon) of 2 cycle oil into the cylinders. Re-install the plugs.

P.S. 

If you have any questions, either call 403 277 0152 or drop in (3924, 3A Street, North East, Calgary, Alberta, T2E 6R4). We offer winterization and premium winter storage at $90 per month

Winter projects / storage packages available, example: spend $1000 and get 1 month free storage.

Personalized Customer Service.

 

 

custom image
 
   
 
 

 

 

   custom image     custom image

 

Back To Top